GLACIER BAY, INC.

SYSTEM STARTUP FORM

This form must be completed in its entirety and submitted at the time of system startup to validate the warranty.

System Information			Owner Information
Startup Date:			Owner's name:
Model #:			Street address:
Serial #:			City/State/Zip:
Manufacture Date:			Country:
			Vessel Information
Number of Refrigerator zones:			Boat make:
Number of Freezer zones:			Model:
Number of Arctic Air zones:			Hull number:
			Service Agent Information
Controls (indicate number and type of each)			Company:
Refrigerator:	ECM	STD	Service technician:
Freezer:	ECM	STD	Contact number:
Arctic Air:	TIMER	DIG	Work performed at (location)
			Technician Certification Number#

Prestart Checkout

Instructions: Locate, verify and check off each item. A description of each can be found in the Installation Manual.

Compressor mounted on non-resonating platform		Yes	No
R/A/D Assembly is mounted upright (vertical)		Yes	No
Suction line (in/out) on R/A/D Assembly is routed correctly		Yes	No
Condenser is mounted upright (vertical)		Yes	No
All joints made with Stay-Brite #8 low-temp solder		Yes	No
No non-factory flare connections		Yes	No
No bends in VBI's		Yes	No
No "oil traps" at suction "tee" connections		Yes	No
All 3/8" liquid lines are the same length running to each "zone"		Yes	No
H-P cut-out Rotolock valve in "service" position		Yes	No
All other Rotolock valves are fully open		Yes	No
Plate temperature probes properly positioned and secured		Yes	No
Box temperature probes properly positioned and secured		Yes	No
All TXV sensing bulbs at 10:00 to 2:00 position and horizontal		Yes	No
All TXV sensing bulbs tightly clamped with metal straps		Yes	No
All TXV sensing bulbs sensing gas flow from correct plate only		Yes	No
Centrifugal pump is positioned to be self-priming		Yes	No	N/A
Positive displacement pump......				N/A
	...has water pre-filter	Yes	No
	...mounted on non-resonating platform	Yes	No
Condenser water flow enters at bottom and discharges at top		Yes	No
Condenser bonding stud connected		Yes	No
Water inlet and discharge thru-hulls are open		Yes	No
All wire control box connections are tinned and tight		Yes	No
Correct circuit breaker is installed		Yes	No
Appropriate wire sizes are used		Yes	No

Charge / Startup

All tests are made using the following units of measurement	Temperature
	Pressure
	Weight

The ambient temperatures at the time of service

Air

Water

Leak Test
Pressurizing Agent (check all that apply)	R-134a	R-22	Nitrogen	Other
Equipment used (check all that apply)			Electronic sniffer
			Ultrasonic detector
			Soap bubbles
			Other

Initial Pressure

Ending Pressure

Total Time (Hrs)

Refrigerant Charge
Total Weight

Superheat Settings - Refrigerator
	BOX 1		BOX 2		BOX 3
	Plate 1	Plate 2	Plate 1	Plate 2	Plate 1
Pressure Drop
Evaporator Exit Temp.
Suction Pressure
Superheat

Pressure Readings (after final superheat adjustment)
Freezer high side	Holding plate surface temp.	Pressure
Freezer low side		Pressure

Refrigerator high side	Holding plate surface temp.	Pressure
Refrigerator low side		Pressure

Compressor Motor Current
Current draw (amps)		Low side pressure

Control Settings (P2 and ST2 for ECM controls only)

BOX 1

BOX 2

BOX 3

ST1

ST2

ST1

ST2

ST1

ST2

Refrigerator

Freezer

Refrigerator and Freezer box pull down sequentially (freezer has priority)

Yes

Arctic Air Option Only
High Side Pressure (after final CPR setting - all blowers on)
Low Side Pressure (after final CPR setting - all blowers on)
Compressor Motor Current Draw - Amps (after final CPR setting - all blowers on)

	Blower 1	Blower 2	Blower 3	Blower 4	Blower 5
Inlet Air Temp. (one zone only)
Discharge Air Temp. (one zone only)

Return to Home page .